Precision-engineered to keep your Sumitomo excavator’s hydraulic system running at peak performance.
If you operate a Sumitomo SH200, SH210, or SH240 excavator, you know that hydraulic system reliability directly affects your bottom line. Every minute of downtime costs money. That’s where the COGENG KM15-P02 pressure sensor comes in—a high-quality, direct-fit replacement component designed to match or exceed OEM specifications at a fraction of the dealer price.
The COGENG KM15-P02 is an electronic hydraulic pressure sensor specifically calibrated for Sumitomo’s SH series excavators. It continuously monitors hydraulic system pressure and transmits real-time data to the machine’s main controller. This information is critical for pump control, engine load management, and overall hydraulic efficiency.
When this sensor fails—which it eventually will on any working excavator—you’ll typically see error codes, erratic pump behaviour, or reduced digging power. Replacing it promptly with a dependable unit like the KM15-P02 restores normal operation and prevents cascading damage to more expensive components.
This pressure sensor is a verified fit for the following Sumitomo excavator models:
Sumitomo SH200 (all series variants)
Sumitomo SH210 (all series variants)
Sumitomo SH240 (all series variants)
Always verify your machine’s parts manual or cross-reference the OEM part number before ordering. If you’re unsure, consult with your equipment dealer or a qualified service technician.
| Feature | Specification |
|---|---|
| Model Number | COGENG KM15-P02 |
| Application | Hydraulic system pressure monitoring |
| Output Signal | Standard voltage output (compatible with Sumitomo ECU) |
| Connector Type | Plug-and-play OEM-style connector |
| Build Material | High-strength stainless steel housing with sealed electronics |
| Operating Temperature | Wide range suitable for extreme job site conditions |
| IP Rating | IP67 rated against dust and water ingress |
The sensor uses a sealed, solid-state design that resists vibration, moisture, and temperature swings—exactly the conditions excavators face daily on demolition sites, quarries, and civil construction projects.
Cost-Effective Without Sacrificing Quality
OEM pressure sensors from the excavator dealer can be surprisingly expensive. The COGENG KM15-P02 provides the same functionality and durability at a significantly lower price point, making it ideal for fleet maintenance budgets.
Direct Replacement—No Modifications Required
This is a true plug-and-play sensor. It plugs directly into your existing wiring harness with no cutting, splicing, or adapter harnesses needed. A typical replacement takes less than 15 minutes with basic hand tools.
Rigorous Quality Control
Each COGENG sensor undergoes calibration testing before leaving the factory, ensuring consistent output accuracy and long-term stability.
How do you know when your Sumitomo excavator needs a new pressure sensor? Watch for these warning signs:
Warning lights or error codes on the monitor display
Sluggish or unresponsive hydraulics, especially under load
Intermittent power loss during digging or lifting operations
Engine over-revving or labouring without corresponding hydraulic response
Visible damage or oil contamination at the sensor connector
If you notice any of these symptoms, don’t postpone diagnosis. A faulty pressure sensor sends incorrect data to the controller, which can result in poor fuel economy, reduced productivity, and accelerated wear on pumps and valves.
Replacing the pressure sensor is straightforward, but follow these best practices for a trouble-free result:
Relieve hydraulic pressure before removing the old sensor. Engage the safety lock lever and cycle the controls with the engine off.
Clean the mounting area thoroughly to prevent dirt from entering the hydraulic system.
Inspect the O-ring or sealing washer—use a new one if the new sensor doesn’t include it.
Tighten to the specified torque. Over-tightening can damage threads or the sensor body.
Clear existing fault codes after installation and test-operate the machine to confirm proper function.
The COGENG KM15-P02 pressure sensor is available through authorised heavy equipment parts distributors and online marketplaces serving the construction and earthmoving industry. When purchasing, confirm that the seller provides genuine COGENG product with full warranty coverage.
Excavator downtime is expensive, but the solution doesn’t have to be. The COGENG KM15-P02 pressure sensor offers Sumitomo SH200, SH210, and SH240 owners a reliable, affordable, and easy-to-install alternative to costly OEM parts. Keep one on your shelf as a spare, and you’ll be back to work in minutes when the next sensor calls it quits.
Keep your Sumitomo digging strong—with COGENG precision parts.
Disclaimer: Sumitomo is a registered trademark of Sumitomo Heavy Industries, Ltd. COGENG is an independent manufacturer of replacement parts and is not affiliated with or endorsed by Sumitomo. Always consult your equipment manual and qualified technician for proper part selection and installation.
Contact COGENG
📞 Phone: +86-185-2913-1515
📧 Email: hugo@cogeng.net
💬 WhatsApp +86-185-2913-1515
💬 WeChat: +86-185-7865-1106
🌐 Website: cogeng.net
